[BTC.com Firmware] The customized firmware of the mining pool S17 series is officially launched, and the net profit can be increased by 40%!

Dear BTC.com mining pool users:

BTC.com mining pool has teamed up with Bitmain’s mining machine firmware development team to launch customized firmware for large miners, which can increase daily net income by 40%!

Revenue improvement data:

Firmware download link:

S17:【Click here to download】

S17Pro: [Click here to download]

Please stay tuned for the firmware of T17 series mining machines.

Customized version mining address (this firmware must use the following address for mining):

cn.tls.ss.btc.com:8443 (North)

sz.tls.ss.btc.com:8443 (South)

eu.tls.ss.btc.com:8443 (Europe)

us.tls.ss.btc.com:8443 (US region)

This address supports machine gun mode. Please refer to the machine gun configuration tutorial: https://help.pool.btc.com/hc/zh-cn/articles/360038579832-%E6%9C%BA%E6%9E%AA%E6%B1%A0

Working Mode:

• Normal mode:

• Lowpower: -1t to -20t

• Overclocking mode (Turbo): from +1t to +20t

(S17/S17Pro is +-20T, T17 is +-10T)

Kind tips:

After changing the overclocking gear, the miner will restart. After restarting, the firmware will run at the set gear target and find the most suitable frequency & voltage combination. This process will last about 40-50 minutes. After this process is completed, the workload will be submitted to the mining pool normally.

Take the s17pro 53T model as an example: after configuring the overclocking mode +15 gears, the standard is 68T, but the actual speed can reach more than 70T. Different machines will fluctuate slightly due to physical reasons.

Overclocking must read:

1. Generally speaking, you can try +15T for the first overclocking. The firmware will actively look for the highest overclocking level. If you find that the actual computing power of the mining machine is far from (selling computing power + actual overclocking level), or the mining machine restarts, you can adjust the overclocking level appropriately. It is recommended to adjust it in steps of 3T.

2. Due to differences in physical environment, temperature, humidity, and heat dissipation conditions, the actual overclocking capabilities of mining machines are different. Even mining machines of the same model and the same batch have different physical properties, so the final overclocking results are different, which is normal.

3. Maintenance requires high standards from the mine operation and maintenance personnel. Overclocking is afraid of high temperature (burning the board, high temperature protection), and frequency reduction is afraid of low temperature (loss of computing power). Depending on the temperature, the mode should be changed from time to time (always pay attention to the fan speed and temperature)

4. Overclocking firmware increases computing power and power consumption. When overclocking for the first time, pay attention to the power consumption. It is recommended to test some machines first to familiarize yourself with the operation.

5. Overclocking is a personal behavior. The damage caused to the machine by overclocking is not covered by the warranty.

6. This firmware is the BTC.com customized official firmware. There are also many high-quality third-party firmwares on the market. Users can freely choose according to their needs.

7. Finally, a warning from BTC.com mining pool: Overclocking is risky, so be careful when operating! Overclocking is risky, so be careful when operating! Overclocking is risky, so be careful when operating!

BTC.com batch tools are fully supported and can be downloaded and used at https://pool.btc.com/tools

The first step is to scan the shelf to be upgraded.

Step 2: Select the one you want to upgrade.

Step 3: Select the working mode and amplification level.

• Normal mode:

• Lowpower: -1t to -20t

• Overclocking mode (Turbo): from +1t to +20t

(S17/S17Pro is +-20T, T17 is +-10T)